For. 10 ml
We recommend applying 3 layers to ensure over 3 weeks of absolute perfection and perfect nail cover.
Always remember to apply base, polish and top even on the tip of the nail (on thickness), this technique will ensure you an impeccable hold.
Remove in just five minutes without EVER smoothing the nail.
The semi-permanent LCI does not damage natural nails.
1. lasts 3 weeks
2. polish training
3. Brilliant effect
4. Catalyze in just 60 sec. with lamp.led
5. DOES NOT contain harmful substances:Formaldehyde, Toluene and DBP
Nail preparation Accessories: Gloves - Lima - Tronchesina - Finishing block - Push cuticles - Pressed cotton pad - Disinfectant - fluidpro®
Let's put on the gloves and get started.
1 We vaporize the customer's tools and hands with the disinfectant. We dry our hands well with a towel.
2 With tronchesine, we cut the excess cuticles
3 We push the small cuticles along the perimeter of the nail, using the cuticle push or orange stick
4 We use the file (side 180) to give the preferred shape to the nails
5* We take the finishing block and evenly mattify the nail
6* Now with a cotton pad moistened with fluidpro, we clean the surface of the nail from the dusty residues
Application of the semi-permanent LCI
Accessories: Color - BASE - TOP - Pressed cotton pad - Cleaner - fluidpro® - UV or LED lamp - Cuticole oil
7* We apply a THIN and HOMOGENEOUS layer of BASE, taking care not to touch the cuticles
8* We catalyze in UV lamp for 120 sec. (in LED lamp 60 sec.)
9 Now, with a DRY pad we eliminate the dispersion released by the BASE, passing it on the surface of the nail. Don't be afraid, let's do it decisively.
What is dispersion? Dispersion can be given by both the BASE, and the TOP. It is a thin and sticky layer caused by the excessive amount of product applied.
10* We apply the first layer of color ( we recommend 3 total layers). Here too, we try not to dirty the cuticles and apply it in a homogeneous and subtle way. We catalyze in UV lamp for 120 sec. (in LED lamp 60 sec.) THIS POINT, LET'S REPEAT IT 3 TIMES (3 layers of color)
11 Now we are ready to apply the TOP. We make a homogeneous, thin layer and catalyze in UV lamp for 240 sec., i.e. 2 timer cycles (in LED lamp 120 sec.).
12* We take a pressed cotton square, moisten with the Cleaner and clean the surface from the dispersion of the TOP.
13 At this point we can apply cuticles oil, distributing a small amount on the perimeter of each nail. We gently massage our fingers and compliments, we finished our manicure with semi-permanent!
5* Be careful not to leave any part of the shiny nail. We always check the backlight that the surface is all completely opaque.
6* Attention, after completing this process we never touch the nail again for any reason, we could fatten it again and this will create possible problems of future tightness.
7* We do not leave any part of the nail not covered by base. Let's check, here too, looking at the backlight surface. I recommend that it be a thin layer, otherwise, a thick layer could give problems of color duration and excessive dispersion.
8* Be careful to place your hand well, so that all fingers are evenly facing under the range of the bulbs. We don't bend our thumbs much, but we try to lay it out as best we can.
10* We must not be in a hurry to see a completely covering effect right away, we last all the steps well. If we dirty the cuticles or skin, we clean with the orange stick moistened with fluidpro before catalyzing in the lamp.
12* To eliminate the dispersion of the TOP, we can also use the fluidpro instead of the Cleaner. But be careful, in this case the passage on the surface of the nail must be quick and light to avoid mattifying the result.
IMPORTANT: Apply the product (base, color, top) also on the tip of the nail before catalyzing in the lamp (TIP CLOSURE technique). This will ensure a long duration of the polish.
Two rolls of pads - 1000 pieces
Top without dispersion, 10ML
Buffer - 5 pieces
Cleaner 50 ml
100 Aluminum foil with cotton pad included
POISON, fragrant cuticle oil, 15ML